HGPS12

Device is resistible to water drops and humidity of environment.

  • Small size 82 x 63 x 28 mm
  • Water drops and humidity resistant
  • 1-Wire interface
  • Low power consumption
  • Internal power supply available (ECO4+)
Request Quotation

Call/ Text Us: (02) 7379-9175

Category:

Explanations

Deep sleep mode – Power saving mode when GPS and GSM modems and all peripheral devices are disabled, except DINs and DOUTs. Device wake up on state change of DIN3 and DIN4.

Device can be installed within 45° angle in any axis but top surface facing up. Device should be installed tightly, does not move or shake.

Warning!

All internal components including battery must be replaced only by manufacturer!

Any self-willed attempt to open device cases will void any warranty. Device must be installed in service access area (e.g. under dashboard, behind fuse box).

Device installation

  • When installing device into vehicle please obey these instructions over wise you device may not work properly.
  • Module should not be seen or easily reached.
  • Module should be firmly fixed to the surface. Please avoid mounting module near the metal surface or cables (see the picture below).
  • Wrong module mounting may be the cause of module malfunction.
  • Module cannot be fixed to heat emitting or moving parts.
  • SIM card should be inserted in the module while the connector is plugged off (while module has no power).
  • Module must be fitted with double sided stick tape!

Antenna installation

It is recommended to place GPS/GLONASS antenna behind the dashboard as close to the window as possible. It must be uncovered, installed heads up (see picture).

Best place for GPS antenna is marked with green in picture.

Dimensions 8.2 × 6.3 × 2.8 cm
Electrical Specification:

󠁪
Power supply

12/24 V DC (range:10 – 32 V DC)
Absolute maximum ratings

50 V @ 60 s, 72 V @ 0.1 s (on ECO4+)
Power Consumption:

󠁪
Deep Sleep

6 mA (ECO4), 7 mA (ECO4+)
Normal mode, battery not charging/full battery

100 mA
Normal mode, battery charging

200 mA (ECO4+)
Internal supply (ECO4+)

Li-Po 3.7 V 190 mAh
Protections

Charging protection (on ECO4+), Electrostatic discharge protection on 1-wire data, Electrostatic discharge protection on sim card slot, Electrostatic discharge protection on USB, Over-current protection on 1-Wire power, Reverse polarity protection, Short circuit protection
Operating environment:

󠁪
Storage temperature

-40 to +65 °C
Operating temperature

-35 to +60 °C
Operating from battery: (charging)

-20 to +45 °C
Operating from battery (discharging)

-20 to +6- °C
Operating altitude

Up to 2000 m
Certification & Approvals:

CE ready, E-mark, FCC HW ready, RoHS, Temp. Test ISO16750
IO Characteristics

󠁪
Digital Inputs

4 x DIN
Threshold

4 V
Digital Outputs

2 x DOUT
Max output

Open collector 32 V, 1 A max
Analog Inputs

2 x AIN
Input range

0 – 30 V
1-Wire

1-Wire peripherals
Output current

80 mA
USB

Configuration interface
Telecommunication, Positioning:

󠁪
GPS/GLONASS module

Ublox MAX-7C Internal 56 channel
Sensitivity

-161 dBm
Cold start

29 s
Aided start

5 s
Reacquisition

1 s
GPS antenna

External
Frequency

1575.42 ± 3 MHz
GSM modem

Quectel M95 Internal GSM850/GSM900/DCS1800/DCS1900
GSM antenna

Internal GSM850/GSM900/DCS1800/DCS1900
Accelerometer

3-axis: 2g/4g/8g/16g
Peripherals

󠁪
Available on 1 - Wire

1 x iButton DS1990 with passive socket, 4 x Temperature sensors DS18B20/DS18S20
Available on digital outputs

1 x Buzzer/LED, 1 x Eco driving panel
Pin out

1-Wire data, 1-Wire power, AIN1, AIN2, Black, Blue, DIN1, DIN2, DIN3, DIN4, DOUT1, DOUT2, Gray, Green, Green with yellow stripe, Ground, Orange, Pink, Power supply, Purple, Red, White, White with red stripe, Yellow

Reviews

There are no reviews yet.

Be the first to review “HGPS12”

Your email address will not be published. Required fields are marked *

Bulk Orders? Request a Quotation!

Related products